Current issue
Archive
About the Journal
About
Editorial Board
Abstract & Indexing
Contact
Editorial Policies
Authorship & COI
Ethical principles
Principles of Transparent Checklist
Open access
For Authors
Instructions to Authors
Detailing Guidelines for Authors
Review process
Review sheet
How to submit
Open Access license
ORIGINAL PAPER
Investigation of coated and uncoated carbide cutting tool wear in dry turning of en aw 2007 aluminum alloy
1
Faculty of Mechanical Engineering, University of Zielona Góra, 4 Prof. Z. Szafrana Street, 65-516 Zielona Gora, Poland
2
Machining Department, Lumel Alucast Sp. z o.o., 1 Słubicka street, 65-127 Zielona Góra, Poland
3
Faculty of Mechanical Engineering, Faculty of Mechanical Engineering, Opole University of Technology, 5 St. Mikołajczyka str., 45-271 Opole, Poland, Pakistan
4
Faculty of Mechanical Engineering, Mersin University, Turkey
Submission date: 2024-03-18
Acceptance date: 2024-06-13
Publication date: 2024-09-12
Corresponding author
Kamil Leksycki
Faculty of Mechanical Engineering, University of Zielona Góra, 4 Prof. Z. Szafrana Street, 65-516 Zielona Gora, Poland
Faculty of Mechanical Engineering, University of Zielona Góra, 4 Prof. Z. Szafrana Street, 65-516 Zielona Gora, Poland
International Journal of Applied Mechanics and Engineering 2024;29(3):69-81
KEYWORDS
TOPICS
ABSTRACT
The automotive, aerospace and marine industries make extensive use of aluminum and its alloys to produce a wide variety of components. This prompts research work related to improving manufacturing processes using these materials. One of the main problems in this area is the durability of cutting tools. This article describes the results of tests on wear of the coated and uncoated carbide cutting tools during turning of EN AW 2007 aluminum alloy. The tests were carried out under dry conditions and at higher cutting speeds. On the face rake, the VBB indicator (average width of the flank wear) and on the rake face, the KB indicator (crater width on the rake face) were evaluated. Only for the uncoated insert, the break-in period, steady-state wear region and intensive wear were observed and the limited alue of the VBB indicator was obtained after 36 minutes of the tool life. The TiAlN+TiN coated insert, as well as TiCN achieved very short tool life periods of 16 and 24 minutes, respectively. Compared to the uncoated and the TiCN coated insert, a VBB increase of about 170% was obtained for the TiAlN+TiN coated insert after 16 minutes. In contrast, an increase in the VBB of almost 60% was obtained for the TiCN coated insert after 24 minutes, compared to the uncoated insert. Compared to the uncoated insert, an increase of 12.1% in the KB value was obtained for the TiCN coated insert, and 18.2% for the TiAlN+TiN coated insert. The main wear mechanism of the tested cutting inserts was the phenomenon of adhesion. Abrasion wear is observed on the surfaces of the TiAlN+TiN and TiCN coated inserts. The TiCN coated insert also showed coating delamination. The build-up edge (BUE) phenomenon is observed on the surfaces of the TiAlN+TiN coated and uncoated inserts.
REFERENCES (24)
1.
Bazaz S.M., Ratava J., Lohtander M. and Varis J. (2023): An investigation of factors influencing tool life in the metal cutting turning process by dimensional analysis.– Machines, vol.11, No.3, pp.393, https://doi.org/10.3390/machin....
2.
Groover M.P. (2020): Fundamentals of Modern Manufacturing: Materials, Processes, and Systems.– John Wiley & Sons: Hoboken, NJ, USA.
3.
Grigoriev S.N., Gurin V.D., Volosova M.A. and Cherkasova N.Y. (2013): Development of residual cutting tool life prediction algorithm by processing on CNC machine tool.– Materialwissenschaft und Werkstofftechnik vol.44, No.9, pp.790-796, https://doi.org/10.1002/mawe.2....
4.
Inspektor A. and Salvador P.A. (2014): Architecture of PVD coatings for metalcutting applications: A review.– Surface and Coatings Technology, vol.257, pp.138-153, https://doi.org/10.1016/j.surf....
5.
Sheikh-Ahmad J. and Davim J.P. (2012): Tool wear in machining processes for composites.– In: Woodhead Publishing Series in Composites Science and Engineering, Machining Technology for Composite Materials (H. Hocheng, Ed.).– Woodhead Publishing, pp.116-153, https://doi.org/10.1533/978085....
6.
Kormaz M.E., Gupta M.K., Celik E., Ross N.S. and Gunay M. (2024): Tool wear and its mechanism in turning aluminum alloys with image processing and machine learning methods.– Tribology International, vol.191, pp.109207, https://doi.org/10.1016/j.trib....
7.
Gupta M.K., Niesłony P., Kormaz M.E., Królczyk G.M., Kuntoglu M., Pawlus P., Jamil M. and Sarikaya M. (2023): Potential use of cryogenic cooling for improving the tribological and tool wear characteristics while machining aluminum alloys.– Tribology International, vol.183, pp.108434, https://doi.org/10.1016/j.trib....
8.
Zhang P., Zhang X., Cao X., Yu X. and Wang Y. (2021): Analysis on the tool wear behavior of 7050-T7451 aluminum alloy under ultrasonic elliptical vibration cutting.– Wear, vol. 466-467, pp.203538, https://doi.org/10.1016/j.wear....
9.
Breidenstein B., Denkena B., Bergmann B., Picker T. and Wolters P. (2023): Tool wear when using natural rocks as cutting material for the turning of aluminum alloys and plastics.– Manufacturing Processes, vol.17, pp.425-435, https://doi.org/10.1007/s11740....
10.
Gupta M.K., Niesłony P., Sarikaya M., Kormaz M.E., Kuntoglu M. and Królczy G.M. (2023): Studies on geometrical features of tool wear and other important machining characteristics in sustainable turning of aluminium alloys.– International Journal of Precision Engineering and Manufacturing-Green Technology, vol.10, pp.943-957, https://doi.org/10.1007/s40684....
11.
Musavi S.H., Sepehrikia M., Davoodi B. and Niknam S.A. (2022): Performance analysis of developed micro-textured cutting tool in machining aluminum alloy 7075-T6: assessment of tool wear and surface roughness.– The International Journal of Advanced Manufacturing Technology, vol.119, pp.3343-3362, https://doi.org/10.1007/s00170....
12.
Pattnaik S.K., Bhoi N.K., Padhi S. and Sarangi S.K. (2017): Dry machining of aluminum for proper selection of cutting tool: tool performance and tool wear.– The International Journal of Advanced Manufacturing Technology, vol.98, pp.55-65, https://doi.org/10.1007/s00170....
13.
Salonitis K. and Kolios A. (2013): Reliability assessment of cutting tools life based on advanced approximation methods.– Peocedia CIRP, vol.8, pp.397-402, https://doi.org/10.1016/j.proc....
14.
Soren T.R., Kumar R., Panigrahi I., Sahoo A.K., Panda A. and Das R.K. (2019): Machinability behavior of aluminium alloys: a brief study.– Materials Today: Proceedings, vol.18, No.7, pp.5069-5075, https://doi.org/10.1016/j.matp....
15.
Santos Jr M.C., Machado A.R., Sales W., Barrozo M.A.S. and Ezugwu E.O. (2016): Machining of aluminum alloys: a review.– The International Journal of Advanced Manufacturing Technology, vol.86, pp.3067-3080, https://doi.org/10.1007/s00170....
16.
Junge T., Mehner T., Nestler A., Schubert A. and Lampke T. (2022): Surface properties in turning of aluminum alloys applying different cooling strategies.– Procedia CIRP, vol.108, pp.246-251, https://doi.org/10.1016/j.proc....
17.
Kumar P., Jain A.K., Chaurasiya P.K., Tiwari D., Gopalan A., Dhanraj J.A., Soloman J.M., Sivakumar A., Velmurugan K. and Rushman J.F. (2022): Sustainable machining using eco-friendly cutting fluids: a review.– Advances in Materials Science and Engineering, vol.2022, pp.1-16, https://doi.org/10.1155/2022/5....
18.
Umaras E., Barari A. and Tsuzuki M.S.G. (2019): intelligent design tolerance allocation for optimum adaptability to manufacturing using a Monte Carlo approach.– IFAC-PapersOnLine, vol.52, No.10, pp.165-170, https://doi.org/10.1016/j.ifac....
19.
Leksycki K., Maruda R.W., Feldshtein E., Wojciechowski S., Habrat W., Gupta M.K. and Królczyk G.M. (2023): Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions.– Tribology International, vol.189, pp.109002, https://doi.org/10.1016/j.trib....
20.
Grzesik W. (2017): Advanced Machining Processes of Metallic Materials: Theory, Modelling, and Applications, Second Edition.– Elsevier.
21.
Stephenson D.A. and Agapiou J.S. (1997): Metal Cutting Theory and Practice, Third Edition.– New York: CRC Press.
22.
Bhushan R.K. (2020): Impact of nose radius and machining parameters on surface roughness, tool wear and tool life during turning of AA7075/SiC composites for green manufacturing.– Mechanics of Advanced Materials and Modern Processes, vol.6, No.1, https://doi.org/10.1186/s40759....
23.
Szczotkarz N., Mrugalski R., Maruda R.W., Królczyk G.M., Legutko S., Leksycki K., Dębowski D. and Pruncu C.I. (2021): Cutting tool wear in turning 316L stainless steel in the conditions of minimized lubrication.– Tribology International, vol.156, pp.106813, https://doi.org/10.1016/j.trib....
24.
Gao L., Hou Z., Li C. Shen R. and Yang T. (2022): Dry turning of SiCp/Al matrix composites with a wide range of particle volume fractions: tool wear characteristics analysis of multi-coated tool.– International Journal of Advanced Manufacturing Technology, vol.121, pp.5343-5359. https://doi.org/10.1007/s00170....
| eISSN: | 2353-9003 |
| ISSN: | 1734-4492 |
Task: edition of a scientific journal, its internationalization and ensuring open access to the journal via the Internet
© 2006-2024 Journal hosting platform by Bentus
We process personal data collected when visiting the website. The function of obtaining information about users and their behavior is carried out by voluntarily entered information in forms and saving cookies in end devices. Data, including cookies, are used to provide services, improve the user experience and to analyze the traffic in accordance with the Privacy policy. Data are also collected and processed by Google Analytics tool (more).
You can change cookies settings in your browser. Restricted use of cookies in the browser configuration may affect some functionalities of the website.
You can change cookies settings in your browser. Restricted use of cookies in the browser configuration may affect some functionalities of the website.
